← Drainage Engineering · UPSSSC JE Agriculture

Chapter 1 of 3

Waterlogging & Salinity — Causes & Control

In the UPSSSC JE Agriculture syllabus under Drainage Engineering · 2 parts

📑 Contents (13 sections)

Part 1 of 2

Waterlogging, Land Reclamation & Drainage

Last reviewed 16 Sept 2026 · 7 min read

Waterlogging

Land is waterlogged when the water table rises so close to the surface that the root zone becomes saturated, air circulation in the soil is cut off and crop yields fall.

A commonly adopted Indian criterion classifies areas with a water table within about 2 m of the ground surface as waterlogged, and 2–3 m as potentially waterlogged (critical depth also depends on soil type, crop and groundwater salinity).

Causes

  1. Seepage from unlined canals and distributaries — the main cause in canal commands.
  2. Over-irrigation and intensive irrigation (excessive water application, no volumetric pricing).
  3. Inadequate natural drainage — flat topography, obstructed natural drains.
  4. Obstruction of drainage by roads, railway embankments, canal banks without adequate cross-drainage.
  5. Impervious sub-soil (hard pan) close to the surface preventing percolation.
  6. Heavy rainfall and flooding; submergence of low-lying land.
  7. Seepage from reservoirs and irregular topography.

Harmful effects

  • Lack of aeration in the root zone — plants cannot respire; bacterial activity (nitrogen fixation) is reduced.
  • Soil remains cold — delayed germination; difficult tillage and delayed sowing.
  • Growth of weeds and aquatic plants.
  • Salinisation (efflorescence) — capillary rise of saline groundwater and evaporation leaves salts at the surface (white crust) → sterile land.
  • Restricted choice of crops; reduced yields.
  • Unhealthy climate — breeding of mosquitoes (malaria).
  • Weakening of foundations of buildings and roads.

Prevention and remedies

  1. Lining of canals and watercourses to reduce seepage.
  2. Intercepting (seepage) drains alongside canals.
  3. Efficient water use — reducing irrigation intensity in affected areas, volumetric assessment, proper land levelling, improved methods (sprinkler, drip).
  4. Optimum use of groundwater — tube well pumping (vertical drainage) and conjunctive use of surface and groundwater.
  5. Improving natural drainage and providing adequate cross-drainage under embankments.
  6. Surface and subsurface drainage systems.
  7. Bio-drainage — plantations of high water-using trees (e.g. eucalyptus) along canals and in affected areas.
  8. Changing cropping pattern (less water-intensive crops).

Soil salinity and alkalinity

Irrigation water always contains some salts; where drainage is poor, salts accumulate.

FormulaClassification of salt-affected soils (US Salinity Laboratory)
Soil EC of saturation extract ESP (exchangeable sodium %) pH
Saline > 4 dS/m < 15 usually < 8.5
Sodic (alkali) < 4 dS/m > 15 usually > 8.5
Saline-sodic > 4 dS/m > 15 usually ≤ 8.5
  • Saline soils ("white alkali") — excess soluble salts (chlorides, sulphates of Na, Ca, Mg); white surface crust; soil structure is usually good. Plants suffer because high osmotic pressure reduces water uptake.
  • Sodic (alkali) soils ("black alkali") — high exchangeable sodium; clay disperses, soil becomes impermeable, hard when dry and sticky when wet; dark surface due to dispersed organic matter; high pH (often above 8.5).
  • Locally known in India as reh, kallar or usar lands.

Reclamation

FormulaLeaching requirement

= EC of irrigation water; = permissible EC of drainage water (root zone); = depth of drainage water; = depth of irrigation water.

Depth of irrigation required: ( = consumptive use depth).

  • Saline soils — leaching with good-quality water (ponding or intermittent) combined with effective drainage to carry away the dissolved salts; scraping the surface crust; growing salt-tolerant crops during reclamation.
  • Sodic soils — sodium must first be replaced by calcium using chemical amendments: gypsum (calcium sulphate) — the most common; also pyrites, sulphur, press mud, calcium chloride, acids. Then leach the displaced sodium out with drainage. Green manuring (e.g. dhaincha), organic matter and salt-tolerant crops (e.g. rice, barley, berseem) help.
  • Saline-sodic soils — apply amendments before leaching; leaching alone would convert them into sodic soils.

Land drainage

Drainage removes excess surface water and lowers the water table to keep the root zone aerated and to leach salts.

Surface drainage

Open channels (field drains, collector drains, main drains) that remove excess rainfall runoff and irrigation tail water. Designed by Manning's formula for a design runoff (e.g. from a design storm of a few days' duration) with gentle slopes, stable side slopes and velocities that neither silt nor scour. Land shaping and grading support surface drainage.

Subsurface drainage

Type Description
Tile drains / perforated pipe drains Clay or concrete tiles with open joints, or corrugated perforated PVC pipes with envelopes (gravel or synthetic filters), laid below the root zone at a gentle slope; water enters through joints/perforations and flows to outlets
Mole drains Unlined cylindrical channels formed in clayey subsoil by a mole plough; cheap but short-lived
Vertical drainage (tube wells) Pumping groundwater to lower the water table; water reused for irrigation if quality permits
Open deep ditches Where pipes are uneconomical; occupy land and need maintenance
  • Drainage coefficient — the depth of water (mm or cm) to be removed from the drained area in 24 hours; it fixes the capacity of drains.
  • Layouts: natural (following depressions), gridiron (parallel laterals on one side of a main), herringbone (laterals on both sides of a main at an angle), intercepting (drain across the path of seepage along the foot of a slope or along a canal).
  • Depth commonly around 1–2 m (below the root zone); minimum slopes and velocities chosen to avoid silting; envelopes prevent entry of soil.

Drain spacing

FormulaEllipse (Donnan) equation — steady state

= drain spacing; = hydraulic conductivity; = drainage coefficient (recharge rate, m/day); = height of the water table midway between drains above the impervious layer; = height of the water in the drains above the impervious layer.

Hooghoudt's equation (drains above the impervious layer, using equivalent depth ):

= height of the water table midway above drain level; , = conductivities above and below the drain level.

Quick check · 5 questions · 3 minutes

Padh liya? Ab dekho kitna yaad raha.

Five exam-level questions from Hydrology & Irrigation Engineering. No timer, no payment.

Worked examples

Worked ExampleExample 1 — leaching requirement

Irrigation water has EC 1.2 dS/m and the crop tolerates root-zone drainage water of 6 dS/m. Consumptive use for the season is 80 cm. Find the leaching requirement and the depth of irrigation.

Solution. (20 cm goes to leaching)

Worked ExampleExample 2 — classification of soil

A soil has EC of saturation extract 6 dS/m, ESP 20 and pH 8.3. Classify it and suggest reclamation.

Solution. EC > 4, ESP > 15, pH ≤ 8.5 → saline-sodic. Apply gypsum first, then leach with good water and provide drainage.

Worked ExampleExample 3 — drain spacing (ellipse equation)

Drains rest on an impervious layer with water standing 1.0 m above it; the water table midway between drains is to be held at 2.0 m above the impervious layer. = 0.5 m/day and drainage coefficient 5 mm/day. Find the spacing.

Solution. →

Frequently tested points

  • Waterlogging: saturated root zone; commonly water table within about 2 m.
  • Main cause in canal commands: seepage from unlined canals; also over-irrigation, poor drainage.
  • Effects: poor aeration, salinisation (efflorescence), weeds, malaria.
  • Remedies: lining, intercepting drains, efficient irrigation, vertical drainage, bio-drainage, drainage systems.
  • Saline: EC > 4, ESP < 15; sodic: EC < 4, ESP > 15, pH > 8.5; saline-sodic: both high.
  • Saline → leaching + drainage; sodic → gypsum then leaching.
  • ; .
  • Drainage coefficient = depth removed per 24 h; ellipse equation .
  • Layouts: natural, gridiron, herringbone, intercepting.
Common MistakeCommon mistakes
  • Leaching a saline-sodic soil before applying gypsum (it turns sodic).
  • Treating EC and ESP limits the other way round.
  • Using and measured from the ground surface instead of from the impervious layer.
Revision SummaryChapter summary
  1. Waterlogging saturates the root zone, mainly due to canal seepage, over-irrigation and poor drainage.
  2. It is prevented by lining, efficient irrigation, groundwater use, bio-drainage and drainage systems.
  3. Salt-affected soils are saline, sodic or saline-sodic by EC, ESP and pH.
  4. Saline soils are reclaimed by leaching with drainage; sodic soils need gypsum or other amendments first.
  5. Surface and subsurface drains are sized by the drainage coefficient and spaced by the ellipse or Hooghoudt equations.

Part 2 of 2

Salt Balance & Reclamation of Saline and Alkaline Soils

Last reviewed 1 Oct 2026 · 9 min read

Salt-affected soils

Salt-affected soils contain soluble salts or exchangeable sodium in amounts that harm crops. In irrigated regions of arid and semi-arid areas, they are a major cause of declining yields and land abandonment.

Causes

  • Rising water table (from canal seepage, over-irrigation, no drainage) bringing salty groundwater near the surface; evaporation leaves salts behind.
  • Irrigation with saline or sodic water without leaching.
  • Poor drainage and low rainfall (salts are not flushed).
  • Seawater intrusion and tidal flooding in coastal areas.
  • Salts from parent material and natural salt-laden groundwater.
  • Deficient management — shallow irrigation, no leaching, no drainage.

Classification (USDA Salinity Laboratory)

Measurements are made on the saturation extract of the soil:

  • EC = electrical conductivity of the saturation extract ( at 25 °C).
  • pH (of the saturated soil paste).
  • ESP = exchangeable sodium percentage = .
  • SAR = sodium adsorption ratio = (concentrations in meq/L).
Type EC (dS/m) ESP pH Features
Normal < 4 < 15 < 8.5 Healthy
Saline (white alkali) > 4 < 15 < 8.5 White salt crust; flocculated soil, good structure; chlorides and sulphates of Na, Ca, Mg
Sodic (alkali / black alkali) < 4 > 15 > 8.5 (often 9–10.5) Dispersed soil, poor structure, hard crust when dry; sodium carbonate present; black organic stains
Saline-sodic > 4 > 15 usually < 8.5 Both problems; behaves as saline until leached, then becomes sodic

(The limits are the standard USDA values; some Indian practice takes pH > 8.2 for sodic soils.)

Effects on crops

  1. Osmotic effect — a high salt concentration lowers the soil water potential, so roots cannot absorb water (physiological drought).
  2. Specific-ion toxicity — sodium, chloride, boron damage plants.
  3. Nutritional imbalance — deficiency of calcium, potassium and micronutrients.
  4. Poor soil structure in sodic soils — dispersion of clay, crusting, low infiltration, poor aeration.
  5. Reduced germination, stunted growth and lower yield.

Crop tolerance: sensitive — beans, citrus, most fruit trees; moderately tolerant — wheat, maize, rice (at high levels), sorghum; tolerant — cotton, barley, sugar beet, date palm, Sesbania. Yield reduction follows a threshold–slope relationship (Maas–Hoffman): .

Salt balance of the root zone

The salt balance of an irrigated field compares the salt that enters with irrigation water and the salt that is removed in the drainage water.

where , are the volume and salt concentration of the irrigation water and , those of the drainage water leaving the root zone. If the salts removed are less than those added, the soil accumulates salt.

Leaching fraction and leaching requirement

The leaching fraction (LF) is the fraction of the applied water that passes below the root zone to carry salts away:

The Leaching Requirement (LR) is the minimum leaching fraction needed to keep the root-zone salinity at or below the tolerance of the crop:

where = salinity of the irrigation water and = the tolerable salinity of the saturation extract for the crop (for a given yield reduction); the factor 5 allows for a concentration factor of about 5 from the drainage water to the saturation extract. (Rhoades' formula.)

The gross irrigation requirement is then (for small LR), or with the crop evapotranspiration.

Worked ExampleExample — leaching requirement

Irrigation water has dS/m. A moderately tolerant crop can accept an extract salinity dS/m for the target yield.

, about 7 %.

If the crop's net requirement is 600 mm, the gross requirement is mm, i.e. an extra 46 mm for leaching. The drainage system must be able to carry away this water.

Finished reading? Test yourself.

A timed chapter test from the UPSSSC JE Agriculture series, on exactly this chapter.

Practice this chapter →