← Engineering Geology · TGPSC Manager (Civil)

Chapter 3 of 5

Groundwater Exploration Methods

In the TGPSC Manager (Civil) syllabus under Engineering Geology · 3 parts

📑 Contents (26 sections)

Part 1 of 3

Engineering Geology for Dams, Reservoirs & Tunnels

Last reviewed 4 Nov 2026 · 3 min read

1. Why geology decides the site

Most dam and tunnel failures and cost overruns come from geology: weak or fractured foundations, leakage paths, faults and unexpected water. A civil engineer therefore needs a geological model of the site before design.

2. Dams — geological requirements

Requirement Why
Strong, sound rock at shallow depth (granite, gneiss, quartzite, massive basalt, well-cemented sandstone) To carry the dam's weight and water thrust without excessive settlement
Impervious foundation and abutments To limit seepage and uplift
No active faults or shear zones across the dam axis Movement or weak gouge can cause failure
Favourable dip of beds — beds dipping upstream are best Downstream-dipping beds can allow sliding and leakage under the dam
Stable abutments and valley slopes Landslides into the reservoir or at the abutments are dangerous
Low seismicity or design for it Earthquake loads and reservoir-induced seismicity
Availability of construction materials Aggregates, impervious clay (for earth dams)

Problem rocks

  • Limestone and dolomite — solution cavities (karst) cause leakage.
  • Shale and clay-rich rocks — weak, swell, slake when wet; slide along bedding.
  • Highly jointed or weathered rock — low strength, high permeability.
  • Gypsum and rock salt — soluble.

Treatment measures

Measure Purpose
Consolidation grouting (shallow) Strengthens and seals jointed rock near the foundation surface
Curtain grouting (deep line) Forms an impervious curtain to cut seepage under the dam
Cut-off trench / diaphragm wall Stops seepage through pervious overburden
Drainage galleries and relief wells Reduce uplift pressure
Dental treatment Removes and backfills weak seams and fault gouge with concrete
Rock bolts and anchors Stabilise abutments

Part 2 of 3

Geological Site Investigation for Engineering Works

Last reviewed 16 Sept 2026 · 9 min read

Objectives of site investigation

  • Determine the geology — rock and soil types, their distribution, thickness and depth to bedrock.
  • Identify geological structures — faults, folds, joints, shear zones, cavities.
  • Assess engineering properties of soils and rocks — strength, permeability, compressibility.
  • Establish groundwater conditions.
  • Identify hazards — landslides, seismicity, liquefaction, subsidence, karst.
  • Locate construction materials — aggregates, impervious and pervious soils, building stone.
  • Provide data for design, construction methods and cost estimates, and reduce unforeseen ground conditions.

Stages of investigation

Stage Activities
1. Desk study Collection of existing data — topographic maps (Survey of India), geological maps and reports (Geological Survey of India), aerial photographs, satellite imagery, previous investigation records, well logs, seismic and flood data
2. Site reconnaissance Walk-over survey — outcrops, landforms, drainage, vegetation, springs, landslides, existing structures and their performance, access
3. Preliminary investigation Geological mapping, a few boreholes/pits, geophysical surveys; compare alternative sites or alignments
4. Detailed investigation Closely spaced boreholes, sampling, in-situ and laboratory tests, detailed mapping for the selected site and structure layout
5. Construction-stage investigation Verification of ground conditions as excavation proceeds — foundation mapping, tunnel face logging, additional drilling
6. Post-construction monitoring Instrumentation — piezometers, inclinometers, settlement gauges, seepage measurements

Remote sensing and aerial photographs

  • Aerial photographs (stereo pairs) reveal lineaments (possible faults, joints), landslides, drainage patterns, rock outcrops, alluvial fans and old channels.
  • Satellite imagery (multispectral) helps regional mapping of lithology, structures, land use and groundwater potential zones.
  • GIS integrates maps and data layers; LiDAR gives high-resolution terrain models.
  • Drainage patterns indicate geology — dendritic (uniform rocks), trellis (folded sedimentary rocks), rectangular (jointed/faulted rocks), radial (domes/volcanoes), annular (eroded domes).

Subsurface exploration

Direct methods

Method Features / use
Test pits Shallow (a few metres), allow direct visual examination and undisturbed block samples; cheap for shallow depths above water table
Trenches Continuous exposure across contacts or faults (e.g. fault trenching to study active faults)
Drifts and adits Horizontal tunnels into hillsides — dam abutments and tunnel sites
Shafts Vertical excavations for deep inspection

Boring methods

Method Principle Suitability
Auger boring Hand or power auger rotated into soil Soft to stiff cohesive soils, shallow depths, above water table; disturbed samples
Wash boring Chopping bit with water jet; cuttings washed up Soils (not boulders/rock); fast; samples highly disturbed — used with separate samplers
Percussion (cable tool) boring Repeated lifting and dropping of a heavy bit; slurry bailed out Gravels, boulders, rock; disturbs material
Rotary drilling Rotating bit with circulating fluid Soils and rocks; fast
Rotary core drilling Diamond/tungsten carbide core barrel (single, double tube, triple tube) recovers rock cores Rock — cores for logging, RQD and testing

Core logging, core recovery and RQD

FormulaCore recovery and RQD

Core recovery ratio (CR)

Rock Quality Designation (Deere)

(Measured along the core centre line on NX-size or similar cores; mechanical breaks from drilling are ignored.)

RQD (%) Rock quality
< 25 Very poor
25–50 Poor
50–75 Fair
75–90 Good
90–100 Excellent

Core logs also record rock type, weathering grade, discontinuity spacing and condition, fracture index and water losses (packer/Lugeon tests for permeability of rock).

Geophysical methods (indirect)

Geophysical methods are rapid and economical for covering large areas, but must be correlated with boreholes.

Seismic refraction

  • Seismic waves generated (hammer/explosive) are detected by geophones; first arrival times are plotted against distance.
  • Wave velocity increases with rock density/soundness — loose soil low velocity, fresh rock high velocity; a velocity increase with depth is required.
  • Used for depth to bedrock, rippability of rock, rock quality.
FormulaTwo-layer refraction

Direct wave: ; refracted wave arrives first beyond the crossover distance .

= depth to the interface; , = velocities in upper and lower layers ().

Electrical resistivity

  • Current passed through the ground between two current electrodes; potential difference measured between two potential electrodes.
  • Resistivity depends on rock type, porosity, water content and salinity — clays and saline water have low resistivity; dry sand, gravel and hard rock high.
  • Wenner array — four equally spaced electrodes (spacing ); Schlumberger array — potential electrodes closely spaced at the centre.
  • Vertical electrical sounding (VES) — increasing spacing to probe deeper layers; profiling — constant spacing along a line.
  • Widely used for groundwater exploration, depth to bedrock, locating clay/saline zones.
FormulaWenner apparent resistivity

Other methods

  • Ground penetrating radar (GPR) — shallow high-resolution imaging (utilities, cavities, pavement layers).
  • Magnetic surveys — magnetic minerals, dykes, buried objects.
  • Gravity surveys — density variations, cavities, basins.
  • Seismic reflection — deep structures (oil exploration).
  • Borehole geophysics — logging within boreholes; cross-hole seismic tests.

Part 3 of 3

Groundwater, Aquifers & Well Hydraulics

Last reviewed 16 Sept 2026 · 7 min read

Occurrence of groundwater

Below the ground surface, water occurs in two main zones:

Zone Description
Zone of aeration (vadose zone) Pores contain both air and water. Sub-zones: soil-water zone (root zone), intermediate vadose zone, capillary fringe (just above the water table, held by capillarity)
Zone of saturation All pores filled with water under pressure ≥ atmospheric; its water is groundwater

The water table (phreatic surface) is the upper surface of the zone of saturation in an unconfined aquifer, where pressure is atmospheric.

Geological formations

Formation Stores water? Transmits water? Example
Aquifer Yes Yes, readily Sand, gravel, fractured rock, cavernous limestone
Aquitard Yes Slowly Sandy clay
Aquiclude Yes (porous) No (practically) Clay
Aquifuge No No Massive unfractured granite

Types of aquifers

  • Unconfined (water-table) aquifer — upper boundary is the water table; recharged directly from the surface.
  • Confined (artesian) aquifer — sandwiched between impervious layers; water is under pressure. The level to which water rises in a well is the piezometric surface. If the piezometric surface is above the ground, the well flows naturally (flowing artesian well).
  • Perched aquifer — a small body of groundwater held above the main water table by a local impervious lens.
  • Leaky (semi-confined) aquifer — bounded by an aquitard that allows some leakage.

Aquifer properties

FormulaAquifer parameters
  • Porosity
  • Specific yield — volume of water drained by gravity ÷ total volume
  • Specific retention — water retained against gravity ÷ total volume
  • Hydraulic conductivity (coefficient of permeability) (m/s or m/day)
  • Intrinsic permeability (m² or darcy) — property of the medium alone
  • Transmissivity (m²/day) — flow through a unit-width strip of the full aquifer thickness under unit gradient
  • Storage coefficient (storativity) — volume of water released per unit surface area per unit decline of head
    • Confined aquifers: very small, about to (from compression of the aquifer and expansion of water)
    • Unconfined aquifers: (typically a few per cent to about 30%)

Clay has high porosity but very low specific yield (high retention); coarse sand and gravel have high specific yield.

Darcy's law

= discharge (Darcy) velocity over the gross area; the actual average seepage velocity ( = effective porosity).

Validity: laminar flow — Reynolds number below about 1 (up to about 10 in practice). Not valid for flow through coarse gravel, fractures with turbulent flow or karst conduits.

Steady radial flow to wells (equilibrium equations)

Assumptions (Dupuit–Thiem): homogeneous, isotropic aquifer of infinite extent; well fully penetrating; flow horizontal and laminar; steady state reached; pumping rate constant.

FormulaConfined aquifer

With well radius , drawdown and radius of influence :

FormulaUnconfined aquifer

= saturated thickness before pumping; = depth of water in the well while pumping.

  • Radius of influence — distance beyond which drawdown is negligible; Sichardt's formula: (, in m; in m/s).
  • Cone of depression — the drawdown surface around the pumped well.
  • Discharge is only moderately sensitive to (it appears inside a logarithm).
  • Specific capacity — a measure of well productivity (decreases with time and pumping rate).

Finished reading? Test yourself.

A timed chapter test from the TGPSC Manager (Civil) series, on exactly this chapter.

Practice this chapter →