Notes library · Technical

⚙️ Steel Structures Notes

Design of steel tension and compression members, beams, girders and connections as per IS 800:2007.

14 of 14 chapters written

✅ Free — no sign-up needed

How ready are you for Steel Structures?

Ten questions from the real syllabus, about five minutes. You will see your score and which subject is holding you back — before you create any account.

10 questions · no timer · no payment

Chapters

  1. 01Structural Steel, Sections & IS 800 Design PhilosophyProperties and grades of structural steel (IS 2062), rolled sections and their designations, advantages and drawbacks of steel, IS 800:2007 limit state design — partial safety factors for materials and loads, section classification (plastic, compact, semi-compact, slender), deflection limits and slenderness limits.Read →
  2. 02Bolted & Riveted ConnectionsTypes of bolts and joints, modes of failure, IS 800:2007 design of bearing-type bolts in shear (shear and bearing capacity with kb), reduction factors for long joints, large grip and packings, bolts in tension and combined shear–tension, prying action, HSFG (friction-grip) bolts, spacing and edge distance rules, efficiency of joints, riveted connections — with solved numericals.Read →
  3. 03Welded ConnectionsWelding processes, advantages and defects, types of welds and joints, fillet and butt welds, effective throat thickness, minimum and maximum weld size, effective length and end returns, design strength of welds (IS 800:2007), welds under eccentric load (in-plane and out-of-plane), intermittent welds, weld symbols — with solved numericals.Read →
  4. 04Tension MembersTypes of tension members, IS 800:2007 design strength — yielding of gross section, rupture of net section (plates, threaded rods, angles with shear lag), block shear; net area with staggered holes; slenderness limits; lug angles and splices; design steps — with solved numericals.Read →
  5. 05Compression Members & Built-up ColumnsSteel struts and columns, effective length, slenderness, Euler buckling and the effect of imperfections, IS 800:2007 design compressive stress using buckling classes and imperfection factors, section selection, single and double angle struts, built-up columns with lacing and battens — with solved numericals.Read →
  6. 06Column Bases — Slab Base, Gusseted Base & GrillagePurpose of column bases, bearing strength of concrete, design of slab (bloom) bases with IS 800 thickness formula, gusseted bases, bases for axial load with moment, anchor (holding-down) bolts, shear transfer, grillage foundations and concrete pedestals — with a solved slab base.Read →
  7. 07Steel Beams — Laterally Supported & UnsupportedTypes of steel beams, laterally restrained beams — design bending strength with section classes and the 1.2Ze limit, shear strength and high shear, deflection; web buckling and web crippling under concentrated loads; lateral–torsional buckling of unrestrained beams (IS 800:2007) with effective length and imperfection factors; purlins and built-up beams — with a solved design.Read →
  8. 08Plate GirdersWhen plate girders are used, components, economical depth and self-weight, proportioning of flanges and web, IS 800:2007 web slenderness limits, shear buckling (simple post-critical and tension field methods), intermediate transverse, longitudinal and bearing stiffeners, flange curtailment, connections and splices — with a solved preliminary design.Read →
  9. 09Gantry GirdersCrane gantry girders in industrial buildings, loads — wheel loads, impact, lateral surge and longitudinal drag (IS 875 Part 2), position of wheels for maximum moment and shear, typical sections (I-section with top channel or plate), design checks for bending about both axes, lateral–torsional buckling, shear, web crippling, deflection limits and fatigue — with a solved load and moment calculation.Read →
  10. 10Roof Trusses & PurlinsComponents of a steel roof, types of roof trusses and their span ranges, pitch, spacing of trusses and purlins, loads on roof trusses — dead load, imposed load on roofs (IS 875 Part 2), wind load (IS 875 Part 3); analysis and member design, design of angle and channel purlins, sag rods, bracing and end bearings — with worked load calculations.Read →
  11. 11Industrial Buildings & Bracing SystemsPlanning of steel industrial buildings, structural framing options (truss on columns, portal frames, pre-engineered buildings), bays, crane columns (stepped, laced, twin), gantry supports, roof and wall cladding, lateral load paths, types of bracing (roof, vertical, longitudinal, knee and eaves bracing), column bases and serviceability considerations.Read →
  12. 12Beam-ColumnsMembers under combined axial force and bending — sources of moments, second-order (P-delta) effects and moment amplification, IS 800:2007 section strength check (reduced plastic moment and simple interaction), member buckling interaction with factors ky, kz and kLT, equivalent uniform moment factors, and combined axial tension with bending — with a solved check.Read →
  13. 13Plastic Analysis & Design of SteelPlastic design philosophy for steel structures, requirements of IS 800:2007 (plastic sections, ductility, restraint, fy limit), plastic moment and shape factor of rolled sections, effect of axial force and shear on plastic moment, collapse mechanisms of beams and portal frames, load factors and design procedure — with solved numericals.Read →
  14. 14Cold-Formed Light-Gauge SteelWhat cold-formed steel sections are, how they are made, common shapes (C, Z, hat, sigma, sheeting), advantages and uses, design code IS 801, local buckling and the effective width concept, distortional and lateral–torsional buckling, stiffened and unstiffened elements, connections (screws, rivets, spot welds) and corrosion protection.Read →

Exams that include Steel Structures

Open your exam to see only the chapters its syllabus asks for.

Quick-revision PDFs

Short printable summaries — read the chapter notes first, revise from these.

8 revision PDFs