Notes library · Technical
🏢 RCC Design Notes
Design of reinforced and prestressed concrete members as per IS 456 and IS 1343.
20 of 20 chapters written
✅ Free — no sign-up needed
How ready are you for RCC Design?
Ten questions from the real syllabus, about five minutes. You will see your score and which subject is holding you back — before you create any account.
10 questions · no timer · no payment
Chapters
- 01Concrete & Reinforcement — Properties and IS 456 RequirementsGrades of concrete and characteristic strength, target mean strength, modulus of elasticity, flexural strength, creep and shrinkage; grades and properties of reinforcing steel; exposure conditions, minimum grade, cement content, water–cement ratio and nominal cover as per IS 456:2000; design stress–strain curves and partial safety factors.Read →
- 02Working Stress MethodPhilosophy and assumptions of working stress design (IS 456 Annex B), permissible stresses in concrete and steel, modular ratio, transformed section; singly reinforced rectangular beams — critical neutral axis, lever arm, moment of resistance, balanced, under- and over-reinforced sections; doubly reinforced and flanged sections, shear and columns in WSM; comparison with limit state method — with solved numericals.Read →
- 03Limit State Method — Principles, Loads & Partial Safety FactorsLimit state philosophy, limit states of collapse and serviceability, characteristic loads and strengths, partial safety factors for loads and materials (IS 456 Table 18), design loads, assumptions for flexure, the stress block, limiting depth of neutral axis and balanced, under- and over-reinforced sections — with solved numericals.Read →
- 04Singly & Doubly Reinforced Beams (Limit State of Collapse: Flexure)Analysis and design of singly reinforced rectangular beams by IS 456 (Annex G), depth of neutral axis, moment of resistance, required steel, minimum and maximum reinforcement, bar spacing and side-face steel; when and how to design doubly reinforced beams with strain compatibility in compression steel; effective span and span-to-depth checks — with solved numericals.Read →
- 05Flanged Beams — T-Beams & L-BeamsMonolithic beam–slab action, T and L beams, effective flange width as per IS 456, neutral axis in the flange or in the web, moment of resistance with Df/d limits (IS 456 Annex G), design steps, transverse reinforcement in flanges, and continuous beams near supports — with solved numericals.Read →
- 06Shear & Torsion in RCC MembersShear behaviour and diagonal tension cracking, nominal shear stress, design shear strength of concrete τc (IS 456 Table 19), maximum shear stress τc,max, vertical stirrups and bent-up bars, minimum shear reinforcement and spacing limits, enhanced shear near supports, shear in slabs, and design for torsion by the equivalent shear and moment approach — with solved numericals.Read →
- 07Bond, Anchorage & Development LengthMechanism of bond, flexural and anchorage bond, design bond stress (IS 456), development length in tension and compression, anchorage by hooks and bends, check of development length at simple supports and points of inflexion, bundled bars, lap splices and curtailment of bars — with solved numericals.Read →
- 08One-Way & Continuous SlabsOne-way vs two-way action, effective span, loads, IS 456 detailing rules for slabs (minimum steel, bar spacing, bar diameter, cover), deflection control by span/depth ratio, shear in slabs, moment and shear coefficients for continuous slabs (Tables 12 and 13), cantilever and chajja slabs — with a full design example.Read →
- 09Two-Way & Flat SlabsTwo-way action and load sharing, Rankine–Grashoff theory, IS 456 Annex D coefficients for simply supported slabs (Table 27) and restrained slabs (Table 26), middle and edge strips, torsion reinforcement at corners, loads on supporting beams, and flat slabs — drops, column heads, direct design method and punching shear — with solved numericals.Read →
- 10Design of StaircasesTerminology and types of stairs, proportioning of rise and tread, structural classification (transversely and longitudinally spanning), IS 456 provisions on effective span, load distribution and depth of section, loads on a waist slab, and a full design of a dog-legged stair flight — with solved numericals.Read →
- 11Short & Long ColumnsClassification of RCC columns (short, slender, braced, unbraced), effective length, minimum eccentricity, axially loaded short columns, longitudinal and transverse reinforcement rules, helically reinforced columns, columns with uniaxial and biaxial bending, and additional moments in slender columns as per IS 456 — with solved numericals.Read →
- 12Design of FootingsTypes of shallow foundations, sizing for safe bearing capacity, net upward pressure, IS 456 critical sections for moment, one-way shear and punching shear, thickness at edge, distribution of steel in rectangular footings, development length, transfer of load at the column base, combined and strap footings, raft foundations — with a full design example.Read →
- 13Retaining WallsTypes of retaining walls, earth pressure on walls (Rankine) including surcharge and water, stability against overturning, sliding and bearing (IS 456 cl. 20), shear key, proportioning of cantilever walls, design of stem, toe and heel, counterfort walls, drainage — with a solved stability and stem-design example.Read →
- 14Water Tanks & Liquid Retaining StructuresClassification of water tanks, why liquid-retaining structures are designed against cracking, IS 3370 design basis (crack width, minimum grade and minimum steel), uncracked-section design used in textbooks, circular tanks with flexible and fixed bases, rectangular tanks, Intze tanks, underground tanks and flotation, staging and joints — with a solved circular tank example.Read →
- 15Prestressed Concrete — Materials, Systems & LossesPrinciple of prestressing, advantages over RCC, pre-tensioning and post-tensioning with their systems (Hoyer, Freyssinet, Magnel–Blaton, Gifford–Udall, Lee–McCall), materials and IS 1343 requirements, bonded and unbonded tendons, and all losses of prestress — elastic shortening, shrinkage, creep, relaxation, friction and anchorage slip — with a solved loss calculation.Read →
- 16Prestressed Members in FlexureStresses at transfer and under service loads, sign conventions, kern points and the pressure line, concordant cable and cable profiles, Magnel's graphical method for prestress and eccentricity, cracking moment, ultimate flexural strength, shear and end-block zones — with solved numericals.Read →
- 17Design of Masonry Structures (IS 1905)Load-bearing masonry, strength of masonry units and mortar, effective height, effective length and effective thickness, slenderness ratio, eccentricity ratio, basic compressive stress and its modification by stress reduction, area reduction and shape modification factors, walls with openings and lintels — with a solved wall check.Read →
- 18RCC Construction — Materials, Formwork & Bar BendingPractical RCC construction — materials checks, formwork requirements and types, IS 456 stripping times, reinforcement cutting, bending and placing, cover blocks and chairs, bar bending schedule with standard deductions and crank length, batching, placing, compaction and curing periods — with worked cutting-length examples.Read →
- 19Reinforced BrickworkWhat reinforced brickwork (RB) is, where it is used — RB slabs, lintels, beams, walls and columns; materials and mortar; construction of RB slabs with bars in joints; design approach and limitations; reinforced brick concrete (RBC) — with a worked lintel load example.Read →
- 20Yield Line Theory of SlabsUltimate load analysis of RC slabs by yield lines — assumptions, rules for yield-line patterns, the virtual-work (work) method, isotropic and orthotropic reinforcement, standard results for one-way, square and rectangular slabs, and why it gives an upper bound.Read →
Exams that include RCC Design
Open your exam to see only the chapters its syllabus asks for.
Quick-revision PDFs
Short printable summaries — read the chapter notes first, revise from these.
12 revision PDFs
Concrete & Steel — Properties & IS 456
🔒 Free account to open this PDFLimit State Method — Flexural Design
🔒 Free account to open this PDFDoubly Reinforced Beams & T-Beams
🔒 Free account to open this PDFShear & Bond Design in Beams
🔒 Free account to open this PDFDesign of One-Way Slabs
🔒 Free account to open this PDFDesign of Two-Way Slabs
🔒 Free account to open this PDFDesign of Columns
🔒 Free account to open this PDFDesign of Footings
🔒 Free account to open this PDFDesign of Retaining Walls
🔒 Free account to open this PDFPrestressed Concrete
🔒 Free account to open this PDFDesign of Water Retaining Structures
🔒 Free account to open this PDFEarthquake Resistant Design (IS 1893)
🔒 Free account to open this PDF